Cooking For Engineers Forum Index Cooking For Engineers
Analytical cooking discussed.
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Sous Vide: Sous Vide Cooking at Home Setup Guide
Goto page Previous  1, 2, 3
 
Post new topic   Reply to topic    Cooking For Engineers Forum Index -> Comments Forum
View previous topic :: View next topic  
Author Message
PedroG



Joined: 17 Apr 2012
Posts: 3

PostPosted: Sun Oct 21, 2012 9:36 am    Post subject: Re: Relatively inexspensive built-in Reply with quote

wizodd wrote:
I'm working on building a heating element/thermostat into the bottom of m kitchen sink. Easy to fill, easy to drain, easy to clean, no storage space.

Could be done with an immersion heater and insulating the outside of the sink (insulated lid optional--but make the top of the lid a cutting board...)

That's a practical idea if you have two or more kitchen sinks. Be aware you will be occupying your kitchen sink for two or three days when cooking tough meat.
Back to top
View user's profile Send private message
Ed
Guest





PostPosted: Mon Feb 18, 2013 7:20 pm    Post subject: Sous vide cooker Reply with quote

I tried a PID controller with a slow cooker and it works fine, but, if you don't want to spend a lot, there are simpler alternatives. The first one that worked well was an electric frying pan with a dial control. I was able to set the dial to maintain a fairly accurate temperature at 55 and 75 centigrade. For a larger volume cooker I picked up a used electric turkey or roasting pan made by Rival, it cost $15 at Goodwill and it worked fine. I use a Taylor thermometer, the thermocouple wire is thin enough to allow the lid to close, I probably could insert the probe through the lid with very little trouble. I would also put a small fish tank pump into the larger pot to provide circulation. I have not tried the final method, but, I think it should work and that is to put a dimmer switch between the power source and the slow cooker to regulate the heat, if it works, it would be much cheaper than a PID controller, just a thought, somebody with better electrical knowledge might comment.
Back to top
senojjones



Joined: 17 Aug 2007
Posts: 2
Location: Jacksonville, Florida

PostPosted: Thu May 16, 2013 3:15 pm    Post subject: sous vide setup Reply with quote

I have a PID controller, crock pot but I find for most things a really nice thick ice chest is fine. Got mine off Ebay and it's really a super insulated shipping container, the walls are 3 inches thick. That chest loses 1 degree F, an hour.

It helps to "preheat" the meat. I use a large pot of water on the stove to heat the water for the ice chest, I heat it a few degrees higher, and fill the chest. Let that stablise. Meanwhile reheat a pot full of water to your desired temp, toss in the meat and remove the whole thing from the heat.

Wait 20 minutes and toss the meat into the ice chest. Now you'll have a much smaller heat loss to content with.

Calibrate your ice chest, use the same volume of water and figure out how much boiling water do i need to add to raise the temp 1 degree, or ice to drop it 1 degree.

A large thick ice chest gives you a very stable water bath, and as long as you check the temp every 20 mins or so and adjust, works very well.
Back to top
View user's profile Send private message
guest
Guest





PostPosted: Sat Jun 15, 2013 4:06 am    Post subject: Sous Vide without the appliance Reply with quote

I have a Fisher Paykel convection oven and the lowest temp is 80 degF. Haven't tested how well it holds that temperature and how much it deviates. Interesting...I never considered using my oven as a sous vide device.
Back to top
Guest






PostPosted: Sun Jul 14, 2013 12:41 am    Post subject: Easy & Cheap Sous Vide Setup Reply with quote

A setup that I've used with good results is as follows:

I put three mason jar rings in an electric fry pan, and then I put a Dutch Oven filled with water on top of them. I pour water or oil into the electric fry pan, and set the fry pan for the temperature I need. I check the temp with thermometers in both the fry pan oil/water, and in the Dutch oven. Once stabilized, the water temp in the Dutch oven seems to track really well, especially if using oil in the fry pan.

A Pork Loin Roast using this setup was absolutely delicious, as were some chicken breasts - not dry at all - and in both cases, the collected juices made fantastic gravies.
Back to top
Guest






PostPosted: Sun Dec 29, 2013 11:39 pm    Post subject: 10.5 qt. Soup Warmers? Reply with quote

I am about to take the sous vide plunge. I was wondering if anyone has any experience or thoughts on using one of these 10.5 quart soup warmers for your heated water bath. They seem to be pretty generic and marketed by lots of people. The reason I am considering one is because the 10.5 quarts would provide more volume than your average crock pot, for example. I was thinking this might be a plus if I had a large roast or something. Thanks for any ideas or feedback!
Back to top
Guest
Guest





PostPosted: Tue Mar 11, 2014 11:28 pm    Post subject: rib roast size plastic bags? Reply with quote Delete this post

I find recipes for cooking rib roasts or leg of lamb in the "largest size bag". The bag to which they refer mush be larger that the Foodsaver bags. Who makes the roast size bags suitable for sous vide ad where can they be purchased? I am not seeing anything online.
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Cooking For Engineers Forum Index -> Comments Forum All times are GMT
Goto page Previous  1, 2, 3
Page 3 of 3

 
Jump to:  
You cannot post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You can delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group