View previous topic :: View next topic |
Author |
Message |
rkaspet
Joined: 03 Oct 2011 Posts: 3
|
Posted: Mon Oct 03, 2011 5:46 pm Post subject: End Grain Cutting board help |
|
|
I am in the market to buy an end grain cutting board... I was thinking of getting a walnut board end grain board. Does anybody have any reviews or thoughts about the boards at [spammer site removed] I cannot seem to find reviews for these boards from this site, however they look quite nice though.
Here are the questions I have, any help would be great!
What should I look for in an end grain board? I’m quite confused as there are too many choices out there and hundreds of different sites.
Is walnut a good choice as far as material? It looks too nice , will it get ruined? Is it too hard/soft?
Is it worth the money to get an end grain board vs edge grain?
If I get one with a gravy channel is that difficult to clean?
They say they use mineral oil and beeswax on them, is that normal? Or should it be sealed with a clear coating of some sort?
Should I get a cutting board with legs / feet on it? Or is it better to have it without feet so I can flip the board over? Toooo many combinationssss , what should I dooo…
Any recommendations would be great! Does anybody have a walnut cutting board like the ones at the site I mentioned? Please send me a message or reply as I do not want to pay so much for something without knowing if it’s a good cutting board.
Sorry if I had too many questions.. Thank you all again! |
|
Back to top |
|
|
Dilbert
Joined: 19 Oct 2007 Posts: 1304 Location: central PA
|
Posted: Mon Oct 03, 2011 7:50 pm Post subject: |
|
|
your apprehensions are well justified.
the domain was created:
Creation Date: 13-jul-2011
there is no phone / address / identification of any kind on the site.
it is registered anonymously:
Administrative Contact:
Private, Registration [spammer site removed]@domainsbyproxy.com
Domains by Proxy, Inc.
DomainsByProxy.com
15111 N. Hayden Rd., Ste 160, PMB 353
Scottsdale, Arizona 85260
United States
(480) 624-2599 Fax -- (480) 624-2598
those kinds of "businesses" do not inspire my confidence, any business that has gone to those lengths to disguise itself is suspect in my book.
their pricing is also not inspiring -
compare to www.theboardsmith.com - he's one of the better known and reputable sources.
the classic for cutting/chopping boards/blocks is maple - other woods are softer.
maple will last a very long time - but given the much lighter duty in a home kitchen, the other woods will also last many years - and indeed stuff like walnut is a tad 'prettier'
regular care with bees wax / mineral oil is standard.
finishes: lacquers, varnishes, urethanes should be avoided.
end grain is considered top notch in terms of being easier on the knife edges.
Last edited by Dilbert on Sat Nov 12, 2011 11:52 pm; edited 2 times in total |
|
Back to top |
|
|
yocona
Joined: 18 Mar 2011 Posts: 47
|
Posted: Mon Oct 03, 2011 11:57 pm Post subject: Re: End Grain Cutting board help |
|
|
rkaspet wrote: |
Here are the questions I have, any help would be great!
What should I look for in an end grain board? I’m quite confused as there are too many choices out there and hundreds of different sites.
Is walnut a good choice as far as material? It looks too nice , will it get ruined? Is it too hard/soft?
Is it worth the money to get an end grain board vs edge grain?
If I get one with a gravy channel is that difficult to clean?
They say they use mineral oil and beeswax on them, is that normal? Or should it be sealed with a clear coating of some sort?
Should I get a cutting board with legs / feet on it? Or is it better to have it without feet so I can flip the board over? Toooo many combinationssss , what should I dooo… |
If you are set on getting an end grain board, I think the most important criterion is to buy it from a company that's been making them for a long time. Personally, I don't think it's worth the extra expense. I have never noticed any difference in knife wear. And if you care for your board properly, either type will last for many years.
No feet. In addition to the impractical aspect of not being able to use both sides, I don't like the feel of cutting on a board with feet. I do like the gravy channel; it's no problem to clean, and really comes in handy when tomatoes are in season.
Absolutely do not apply any kind of sealer. Wood has natural anti-bacterial properties, and a sealer would eliminate that benefit. All you need is mineral oil, which you can buy in any drug store or large grocery store.
The choice of wood really comes down to personal preference. Maple is my preference because I prefer the feel. (Aesthetically, I couldn't care less.) I also have a polyurethane board reserved exclusively for raw proteins, solely because poly boards can be put in a dishwasher and/or bleached. With a kitchen towel on the counter beneath the board, the feel isn't bad. |
|
Back to top |
|
|
GaryProtein
Joined: 26 Oct 2005 Posts: 535
|
Posted: Thu Oct 06, 2011 8:19 pm Post subject: |
|
|
Take a look at this company: http://www.cuttingboardgallery.com/
They have been in business for a long time. Also, the Food Network uses their boards (and I have one of them) and I'm very pleased with it.
I always liked the look of the walnut boards, but was initially afraid that being dark, it would be harder to use and to see my fingers than a light colored maple board. After using the board, I liked it better than maple because my fingers showed up better and had better contrast against the walnut than maple, making them easier to see so I don't cut them, since I don't chop without looking like the professional chefs.
I like the board very much. Whether it is worth the increase in money, is a personal concern. I would buy another one if the need arises. |
|
Back to top |
|
|
rkaspet
Joined: 03 Oct 2011 Posts: 3
|
Posted: Mon Oct 17, 2011 3:24 am Post subject: End Grain Cutting boards |
|
|
I ended up going with [spammer site removedl] the site I mentioned before, I just liked the way the walnut boards looked that they had.. I called them up and the were actually quite helpful.. turns out they are made like 30 mins from me so im going to drop by their woodshop to pick it up tomorrow woohoo! Ill let everyone know how it is when I get it back to my countertop. |
|
Back to top |
|
|
rkaspet
Joined: 03 Oct 2011 Posts: 3
|
Posted: Thu Nov 10, 2011 6:54 pm Post subject: |
|
|
I figured I would update everyone--- Ive been using the board I got for a about a week now, all the joints are tight and precise, I got it with feet on it, which Im happy i did, keeps it from trapping moisture under the board... im extremely happy with it and will likely buy some for my family for the holidays.. |
|
Back to top |
|
|
Jim Cooley
Joined: 09 Oct 2008 Posts: 377 Location: Seattle
|
Posted: Thu Nov 10, 2011 10:47 pm Post subject: |
|
|
Thanks for the update. Please check in after a year or two... |
|
Back to top |
|
|
Dilbert
Joined: 19 Oct 2007 Posts: 1304 Location: central PA
|
|
Back to top |
|
|
Michael Chu
Joined: 10 May 2005 Posts: 1654 Location: Austin, TX (USA)
|
Posted: Mon Nov 14, 2011 4:00 am Post subject: |
|
|
Nice catch Dilbert! |
|
Back to top |
|
|
yocona
Joined: 18 Mar 2011 Posts: 47
|
Posted: Mon Nov 14, 2011 11:33 am Post subject: |
|
|
Wow. Then I guess it's not a surprise after all, that he lives 30 minutes from the business in question. |
|
Back to top |
|
|
The BoardSMITH
Joined: 14 May 2008 Posts: 8 Location: High Point, NC
|
Posted: Tue Nov 15, 2011 12:12 pm Post subject: |
|
|
Very observent Dilbert. I saw these threads myself and wondered why there were so many and you caught him! Shameless! Makes the honest makers look bad. |
|
Back to top |
|
|
Dilbert
Joined: 19 Oct 2007 Posts: 1304 Location: central PA
|
Posted: Wed Nov 16, 2011 11:54 pm Post subject: |
|
|
I'm not so sure it makes the good guys look bad - perhaps to the internet novice - but I smelled a rat from the beginning. the continuing shill postings were a big red flag and once one compares dates, well . . . .
btw, I'm still looking to get a custom knife block. did you get my PM a thousand years back? |
|
Back to top |
|
|
The BoardSMITH
Joined: 14 May 2008 Posts: 8 Location: High Point, NC
|
Posted: Tue Nov 29, 2011 12:23 pm Post subject: |
|
|
Sorry, I'm not making knife blocks any further for a host of reasons I'll not bore anyone here with. I will stick with what I know best without trying to trick and fool anyone into buying one from me like the OP in this thread. |
|
Back to top |
|
|
|